FREE DELIVERY ON ORDERS OVER £100

How to Measure Your Campervan Bed for a Sleeping Mat

World of Camping |

Before choosing a campervan sleeping mat, measure the bed in its actual sleeping position. You need the usable length, the width at several points, the platform's shape and enough clearance for the inflated mat, bedding and access. Measure packed storage separately: a mat that fits your bed may not fit the cupboard where you want to keep it.

This guide helps you record those measurements for a campervan conversion, a car-camping platform or a pop-top roof bed. It is a fit-checking method, not a vehicle compatibility guarantee. Always follow the instructions for your bed, roof and sleeping mat.

What you need

  • A tape measure, ideally with someone to help hold the other end.
  • A notebook or phone for measurements and a simple sketch.
  • A torch for checking corners and fittings.
  • The bed or roof manufacturer's instructions where relevant.
  • The exact mat specification and outline you are considering.

1. Put the bed into its overnight position

Set up the sleeping space exactly as you will use it. Extend a rock-and-roll bed or slide-out platform fully, arrange the seats as instructed and put any required support panels into place. Measure the surface that will support the mat, not the outside of the bed frame.

If you plan to use a mat on top of existing cushions or a mattress, include those in the setup. Their height and shape can change usable space. Do not assume that a photograph of the same vehicle model shows your conversion or bed arrangement.

2. Measure the usable length

Measure from the head end to the foot end along the supported sleeping surface. Repeat the measurement near both sides if the platform is not square. Note the shortest usable length and mark any obstruction on your sketch.

Allow for the real overnight arrangement, including doors, cupboards or seats that must remain in position. Do not rely on an inflated mat hanging beyond the platform unless the bed and mat manufacturers explicitly permit that arrangement.

3. Measure width at several points

Record the width at the head end, middle and foot end, plus anywhere a wheel arch, cupboard, trim panel or fitting narrows the space. Record where each measurement was taken along the bed. This helps you compare the outline rather than just two headline numbers.

For a rectangular mat, the narrowest relevant section can be the deciding measurement. For a shaped car-camping mat, compare the manufacturer's outline with your sketch. A width written as 132/99 cm does not mean the mat is 132 cm wide throughout, and those two figures alone do not tell you exactly where it narrows.

4. Check corners, contours and support

Look for rounded corners, sloping sides, seat hinges, gaps and changes in platform height. A mat can match the overall length and maximum width yet still sit awkwardly around a fixed fitting.

If helpful, mark the proposed outline on the empty platform with paper or a loose template. Do not obstruct mechanisms or use a template as proof that the inflated mat will fit: the actual mat has depth, seams and valves too. Check whether the manufacturer provides an outline drawing or additional dimensions when the shape is unclear.

5. Account for inflated thickness and headroom

Compare the mat's inflated thickness with the vertical space above the sleeping platform. Consider your existing mattress or cushions, bedding, sitting space and the practical clearance needed to get in and out.

For example, a mat listed as 200 x 114 x 10 cm needs a different depth allowance from one listed as 200 x 114 x 7.5 cm. The shared footprint does not make the two interchangeable in a confined sleeping space.

Do not choose an oversized or overly thick mat on the assumption that underinflating it will solve a fit problem. Follow its instructions for inflation and firmness adjustment, and choose a model suited to the available space.

6. Leave access to valves and built-in pumps

Check where the valve, pump controls and charging connection sit when the mat is in position. You need to operate them without forcing the mat against furniture or trapping components.

If you are considering a built-in-pump mat, check the instructions for inflation, deflation and charging. Think through the whole routine: positioning the mat, accessing the controls, adjusting firmness and packing it away the next morning.

7. Treat pop-top roof beds as a separate fit check

Measure the roof-bed platform's usable length, widths and shape, then check the roof manufacturer's permitted mattress depth and bedding arrangements. Roof mechanisms and closing clearances vary between conversions and generations.

Never assume that a mat described as suitable for a pop-top can remain inflated when the roof is closed. Follow the roof manufacturer's procedure, keep bedding and equipment clear of moving parts, and do not force the roof closed. If the permitted arrangement is unclear, confirm it with the roof or conversion manufacturer before using an additional mat.

8. Measure packed storage separately

Check the mat's listed pack size against the actual space where you will store it. Measure the compartment opening as well as the interior: a bag can fit inside a locker but still be difficult to pass through its door.

Allow for other equipment carried in the same space. Do not assume a storage claim for one vehicle trim, year or boot layout applies to every version. Check the supplied packing instructions and practise packing the mat before your first trip.

Your campervan mat measuring checklist

Copy this checklist into your phone and complete it before comparing models.

  • Vehicle, year and bed or conversion model:
  • Bed set up in its normal sleeping position:
  • Usable length on the left, centre and right:
  • Width at the head, middle and foot:
  • Narrowest points and their positions along the bed:
  • Rounded corners, fittings, gaps and changes in height:
  • Existing mattress or cushion thickness:
  • Available headroom and permitted additional mattress depth:
  • Valve and pump access:
  • Pop-top closing instructions checked, if relevant:
  • Storage opening and usable interior dimensions:
  • Chosen mat's exact product code and full inflated dimensions:
  • Manufacturer's outline or fit confirmation checked where needed:

Compare the measurements with the exact mat

Use your completed sketch to compare the full inflated footprint, depth and valve position. Do not add a universal allowance or assume every flexible mat can be squeezed into a smaller bed. If measurements are close or the shape is unclear, ask for more detail before ordering.

Product codes matter as well as names. Different generations can share a model name but have different weights, packed sizes or insulation figures. Keep all comparison figures tied to the exact version you intend to buy.

For a worked range comparison, read Outwell Highway sleeping mats compared: which fits your campervan or car? It explains the differences between Campervan, Campercar, Pump and Pop Top Air models, including their listed dimensions and shaped footprints.

Frequently asked questions

Can I choose a sleeping mat using my vehicle model alone?

No. Vehicle year, seats, furniture and bed conversion can change the available space. Use the vehicle name to narrow your search, then check your actual bed against the full mat dimensions and outline.

Should I measure the bed frame or the mattress area?

Measure the usable supported surface where the mat will sit in the overnight setup. Note frames and fittings separately if they restrict the footprint, depth or valve access.

What if my bed is wider at one end?

Measure the width at several points and record where it changes. Compare those positions with the mat's outline, particularly for shaped car-camping mats. A maximum width alone is not enough.

How much smaller should the mat be than the bed?

There is no single allowance that suits every mat and platform. Check the manufacturer's fit guidance, the inflated outline, valve position and any required clearances. Do not rely on squeezing a larger mat into a smaller space.

Can I put a sleeping mat on my existing campervan mattress?

Check the bed and mat manufacturers' guidance for that arrangement. Include the existing mattress in your height and headroom measurements, and check any roof-closing restrictions.

Can I close a pop-top roof with the mat inflated?

Only follow an arrangement expressly permitted by your roof manufacturer. Do not assume compatibility based on the mat's vehicle description or footprint. Check mattress depth, bedding clearance and the closing procedure.

Does fitting in the boot prove a car-camping mat fits for sleeping?

No. Packed storage and inflated sleeping fit are separate checks. Compare the packed bag with the storage opening and compartment, then compare the inflated mat with the full overnight platform.

What should I send if I need help choosing?

Have your vehicle year, bed or conversion details, a measurement sketch, photographs of the empty sleeping platform and the exact mat product code ready. That makes a fit enquiry more useful, though any remaining uncertainty should be checked with the relevant manufacturer.

EMPTY DOM REMOVE PROTECTOR